Skip to content
IntoInversion
Find your table
IntoInversion
Find your table

Buying guide

Heavy Duty Inversion Table for 400 lbs? The Real Weight Limits, Checked Maker by Maker

By the IntoInversion teamUpdated

We earn from qualifying purchases made through our links.

A heavyset man standing beside a sturdy inversion table in a garage home gym, one hand on its side handle
Innova ITX1200 inversion table with a black padded backrest, a lumbar pad, tall upright handles and ankle holders, on a grey steel frame

Our pick above 300 lb

Innova ITX1200

No, there is no 400 lb inversion table we could verify. The highest verified rating is 350 lb, and the ITX1200 is the best documented table at that ceiling.

  • Rated to 350 lb on Innova's own product page, the highest verified rating
  • Fits users from 4'10" to 6'6", with a three-position pin
  • 50 lb of headroom over the standard 300 lb rating
Weight limit
350 lb
User height
4'10" to 6'6"
Warranty
1 year
Price range
Mid-range

We are not linking to this model at the moment.

Why we picked it

Maker sourceSpecs from the maker's own product page

If you searched for a 400 lb capacity inversion table, you probably already know the standard 300 lb rating doesn’t leave you enough room. We did not test these tables on people, but we checked every capacity against the manufacturers’ own pages and manuals, and if you buy through our links we may earn a commission that has no say in which table we pick.

The Short Answer: No Verified Inversion Table Has a 400 lb Capacity

Weight limits are the spec most often inflated in listings, because a bigger number sells. So we started from the manufacturer, not the product title.

What We Checked

We went to the makers behind the tables that show up for capacity searches: Innova, Teeter, HARISON, Ironman, Sunny Health & Fitness and Health Mark, among others. For each one we looked for the capacity on a page or document the manufacturer controls: a product page, an owner’s manual, or the maker’s own blog. A number that only appears in a marketplace title did not count, because anyone selling the table can type any number into a title.

Why 350 lb Is the Real Ceiling

Three tables from three different makers land on exactly the same figure. Innova publishes “a 350 lbs. weight capacity” for its ITX1200 (Innova). HARISON writes that its HR-407 can carry users “up to 350 lbs heavy” (HARISON).

And the Ironman Gravity 4000 has “a maximum weight capacity of 350 lbs or 159 kgs,” according to the owner’s manual as hosted on ManualsLib (Ironman manual, via ManualsLib). Nothing we could confirm with a manufacturer goes higher and is still on sale.

One older table did publish more. Health Gear’s own product page for the ITM7.5, as archived in October 2024, rated it for “a 400 lb. weight capacity” (Health Gear, 2024 archive).

But Extreme Products Group, the company behind Health Gear, states on its own site that it “has ceased operations and is no longer in business” (Extreme Products Group, 2025), and it filed for Chapter 7 bankruptcy in September 2025, according to BankruptcyObserver (BankruptcyObserver, 2025). With no maker behind it, the ITM7.5 is a historical spec rather than a table you can buy and have supported today; our Health Gear inversion table page has the full record.

What This Page Won’t Tell You

We won’t tell you a 400, 500 or 600 lb inversion table is available to buy, because we could not confirm one. If a site recommends one, ask where the number comes from. In our research, the answer was always one of three things: a traction bench, a discontinued model, or a listing with no manufacturer behind it.

The 350 lb Inversion Tables: What Each Maker Actually Publishes

These are the three tables that reach the verified ceiling, plus one Teeter machine that isn’t a table but reaches the same number. They share the capacity, but not how well documented that capacity is.

ProductPublished capacityWhere the number comes fromCan we link it?
Innova ITX1200350 lbInnova’s product pageYes, our pick
HARISON HR-407350 lbHARISON’s own blog postNo verified listing yet
Ironman Gravity 4000350 lbOwner’s manual, as hosted on ManualsLibNo verified listing yet
Teeter DEX II (not a table)350 lbTeeter’s product page and manualYes

Innova ITX1200: Our Pick Above 300 lb

The ITX1200 is the only table in Innova’s range rated above 300 lb, and Innova states it on the product page itself, with user heights of 4’10” to 6’6” and a three-position pin (Innova). That makes it the best documented 350 lb table we found: the capacity, the height range and the angle system are all on a page Innova controls, not in a blog post or a third-party copy of a manual.

Innova ITX1200 inversion table with a black padded backrest, a lumbar pad, tall upright handles and ankle holders, on a grey steel frame

Rated to 350 lbMaker source

by Innova

Best for users over 300 lb who want a capacity the maker states itself.

Skip it if you weigh more than 350 lb: going over the published rating means using the table outside what the maker says it was built for.

It is the only table from either Innova or Teeter that the maker rates above 300 lb: Innova publishes 350 lb for it, where every other model in both ranges stops at 300 lb or lower.

Weight limit
350 lb
User height
4'10" to 6'6"
Warranty
1 year
Price range
Mid-range

What we like

  • 350 lb capacity, the highest in the Innova and Teeter ranges
  • Adjustable stretch bars for a fuller stretch at lower slopes
  • Reversible ankle holding system
  • Pin with a protective cover

Keep in mind

  • Only three pin positions, with degrees not stated
  • One-year limited warranty
  • Max height 6 ft 6 in, the same as the 300 lb models
  • No heat or massage

We are not linking to this model at the moment. The specs below still hold. See the alternatives we would pick instead.

Full specs
Price range
Mid-range
Weight capacity
350 lb
User height
4'10" to 6'6"
Angle control
Three-position pin with protective cover; degrees not stated; adjustable stretch bars for a fuller stretch at lower slopes
Ankle system
Reversible ankle holding system
Heat and massage
None
Warranty
1 year limited
FDA
Not stated

Maker sourceFrom the maker's product page. Not stated means the maker publishes nothing.

It also comes with Innova’s standard one-year limited warranty, which covers only the original purchaser buying from an authorized retailer for personal use (Innova). That wording is from Innova’s ITX9600 manual; the ITX1200 page states the same one-year term. Innova does not state an FDA status for this table.

One practical caveat: stock on the ITX1200 has been limited, and it moves week to week. The card above shows the current availability. If it reads as scarce or unavailable, the spec still holds; it is the supply that changes.

HARISON HR-407: 350 lb on the Maker’s Own Blog

HARISON publishes the HR-407 at 350 lb, matching the ITX1200 rather than beating it (HARISON). The catch is where the number lives. It appears in a post on HARISON’s blog, not on a structured spec sheet, and the store page for the same table does not repeat the capacity or a height range. What the store page does state is a 12-month warranty (HARISON), and when we checked in September 2026 it showed the table as out of stock.

We don’t have a verified listing for the HR-407, so there is no product card for it here. If you find one, the 350 lb figure is real; just check that the seller is shipping the HR-407 and not a lookalike.

Ironman Inversion Table Weight Limit

The Ironman Gravity 4000 has a maximum weight capacity of 350 lb, according to the owner’s manual as hosted on ManualsLib (Ironman manual, via ManualsLib). That figure comes from the hosted copy of the manual rather than a current Ironman product page, so treat it as the manual’s number, not a spec we could confirm with the maker. HARISON’s blog, comparing the two, also puts the Ironman at 350 lb (HARISON), which is consistent, though it is a competitor talking.

Ironman is sometimes described as having higher-capacity models. We found nothing from the brand above 350 lb, and no new Ironman table on Amazon US in September 2026; our Ironman inversion table weight limit and replacement guide covers what exists and what replaces it.

Teeter DEX II: 350 lb Without Hanging From Your Ankles

Teeter’s inversion tables all stop at 300 lb, but its DEX II is rated to 350 lb for users from 4 ft 8 in to 6 ft 6 in (Teeter DEX II product page), and the manual makes that a hard limit: do not use it “if you are over 6 ft 6 in (198 cm) or over 350 lbs. (159 kg)” (Teeter DEX II manual). It is not an inversion table. You tip forward over a lap pad with your knees and hips bent, and your weight rests on your hips and thighs, with no load on the ankles.

That matters on this page more than on any other, because the ankles are the weak point for heavier users, as the safety section below explains. The trade-offs are real: there is no adjustable angle, only one forward stop, and the machine doesn’t fold. Our Teeter DEX II review covers how it works and who it suits.

Teeter DEX II back decompression device and back extension bench, an alternative to an inversion table, with a black steel frame with foam leg rollers, a padded hip rest and tall handles

Hip-supported, no ankle loadMaker source

by TEETER

Best for users up to 350 lb who would rather not hang their full weight from their ankles.

Skip it if you want a true inversion table with an adjustable angle: the ITX1200 is the table at this rating.

If hanging by your ankles is the problem, the DEX II takes the ankles out: it holds you at the hips and thighs with your knees bent, and Teeter rates it to 350 lb, 50 lb more than any FitSpine table.

Weight limit
350 lb
User height
4'8" to 6'6"
Warranty
5 years
Price range
Premium

What we like

  • Holds you at the hips and thighs, with no load on the ankles
  • Rated to 350 lb for users from 4 ft 8 in to 6 ft 6 in
  • Doubles as a back extension and ab crunch station
  • Five-year full warranty, like the FitSpine tables

Keep in mind

  • No angle setting: one forward stop, so no gentle 20° start
  • Does not fold; Teeter says it is often left set up
  • The manual asks new users for a spotter strong enough to lift them
  • No heat or massage
Full specs
Price range
Premium
Weight capacity
350 lb
User height
4'8" to 6'6"
Angle control
No angle setting: rotates forward to one fixed stop, knees and hips bent at about 90/90
Ankle system
None: your thighs lock between the leg supports and the lap pad, with no load on the ankles
Door and frame fit
Lap pad height set so your hips line up with its top edge; leg supports snug behind the thighs
Mounting
Five steps in the manual, two wrenches and a screwdriver supplied; BILT app instructions
Use
Stand on the base, lean forward on the cane handles and rotate until the lap pad reaches its stop, knees bent
Warranty
5 years full (5-year extension sold separately)
FDA
Manual states Teeter inversion products are FDA-registered as 510(k) devices (brand-wide, no DEX-specific number)

Maker sourceFrom the maker's product page. Not stated means the maker publishes nothing.

We may earn a commission. It never changes what we pick, or the order picks appear in.

How 350 lb Compares With a Standard Table

For context, here is the ITX1200 next to two of the most common tables from Innova and Teeter. Every cell comes from the manufacturer; where a maker publishes nothing, the table says so.

The 350 lb pick next to two standard 300 lb tables
SpecInnova ITX1200 inversion table with a black padded backrest, a lumbar pad, tall upright handles and ankle holders, on a grey steel frameInnova ITX1200Mid-range, price tier 2 of 3Maker sourceInnova ITX9600 inversion table with a black and grey padded backrest, an adjustable headrest, a lumbar pillow and ankle holders, on a grey steel frameInnova ITX9600Budget, price tier 1 of 3Maker sourceTeeter FitSpine LX9 inversion table with a black flexible bed dotted with blue acupressure nodes, curved side handles, blue ankle clamps and a black floor platformTeeter FitSpine LX9Premium, price tier 3 of 3Maker source
Weight capacity350 lbHighest here300 lb300 lb
User height4'10" to 6'6"4'10" to 6'6"4'8" to 6'6"
Ankle systemReversible ankle holding systemReversible ankle holders (foam rollers and U-shaped holders can trade places)Deluxe EZ-Reach ankle lock with Ankle Comfort Dial
Warranty1 year limited1 year limited5 years (extension to 10 sold separately)Highest here
BuyNot linkedSee today's price: Innova ITX9600 on Amazon (opens in a new tab)See today's price: Teeter FitSpine LX9 on Amazon (opens in a new tab)
Innova ITX1200 inversion table with a black padded backrest, a lumbar pad, tall upright handles and ankle holders, on a grey steel frameInnova ITX1200Maker source
Weight capacity
350 lbHighest here
User height
4'10" to 6'6"
Ankle system
Reversible ankle holding system
Warranty
1 year limited
Innova ITX9600 inversion table with a black and grey padded backrest, an adjustable headrest, a lumbar pillow and ankle holders, on a grey steel frameInnova ITX9600Maker source
Weight capacity
300 lb
User height
4'10" to 6'6"
Ankle system
Reversible ankle holders (foam rollers and U-shaped holders can trade places)
Warranty
1 year limited
See today's price: Innova ITX9600 on Amazon (opens in a new tab)
Teeter FitSpine LX9 inversion table with a black flexible bed dotted with blue acupressure nodes, curved side handles, blue ankle clamps and a black floor platformTeeter FitSpine LX9Maker source
Weight capacity
300 lb
User height
4'8" to 6'6"
Ankle system
Deluxe EZ-Reach ankle lock with Ankle Comfort Dial
Warranty
5 years (extension to 10 sold separately)Highest here
See today's price: Teeter FitSpine LX9 on Amazon (opens in a new tab)

Maker source from the maker's own page or manual, not independently testedListing only retail listing, no maker spec sheetNot stated the maker publishes nothing

Sources: Innova ITX1200 · Innova ITX9600 · Teeter FitSpine LX9

Fifty pounds of extra rating is the whole difference in capacity. The height ceiling is the same 6’6” on all three, so a table rated for more weight does not make room for a taller body. If height is your constraint as much as weight, our page on inversion tables for big, tall and large people looks at the whole body profile, not only the number on the frame.

Every Teeter and Innova table we verified, by weight capacity
  • Teeter FitSpine X1300 lb
  • Teeter FitSpine X3300 lb
  • Teeter FitSpine LX9300 lb
  • Innova ITX9600300 lb
  • Innova ITM4800300 lb
  • Innova ITM5900300 lb
  • Innova ITM6000300 lb
  • Innova ITX9900300 lb
  • Innova ITX1200350 lb

Source: Teeter FitSpine X1, FitSpine X3, FitSpine LX9; Innova ITX9600, ITM4800, ITM5900, ITM6000, ITX9900, ITX1200.

Inversion Table Weight Limit by Brand

The weight limit of an inversion table depends on the brand and the model, and the published figures sit in a narrow band.

Teeter, Innova and Ironman Side by Side

BrandHighest inversion table limitSource
Teeter300 lb (the DEX II, which is not a table, is rated 350 lb)Teeter’s product pages and manual
Innova350 lb (ITX1200); 300 lb or lower on its other modelsInnova’s product page
Ironman350 lb (Gravity 4000)Owner’s manual, as hosted on ManualsLib

Teeter rates the DEX II to 350 lb (Teeter DEX II product page), Innova publishes 350 lb for the ITX1200 (Innova), and the Gravity 4000 manual gives the same 350 lb maximum (Ironman manual, via ManualsLib).

What the Brand Limits Mean for You

If you are at or near 300 lb, a Teeter inversion table leaves no margin and the ITX1200 is the table to look at. At 350 lb, every verified inversion table is at its ceiling. Among tables sold today, we did not find a brand that publishes more; the Health Gear ITM7.5 above is a discontinued exception.

Heavy Duty Inversion Tables Rated for 400 lbs: What Exists

If you searched for a heavy duty inversion table at 400 lbs, you were probably looking for one built to carry more weight. The label won’t tell you that. “Heavy duty” is not a regulated term and it is not a number: no standard defines it, and a maker can print it on a table rated for 300 lb as easily as on one rated for 350 lb. So we read what Teeter, Innova and HARISON actually publish about how their frames are built, separately from the capacity figure.

What the Makers Say About Their Steel

Teeter describes the frame of its FitSpine X1, X3 and LX9 in identical words on all three product pages: “High-Grade Heat-Treated Steel FitSpine is 73% stronger and 10X as durable as the competition” (Teeter). That is Teeter’s claim, not a measurement anyone can check. The page does not say who “the competition” is, what was tested, or how.

Innova’s version is shorter. The model comparison on its ITX1200 page makes one construction claim for the whole line, “Heavy Duty Steel,” with the same wording for every model compared and no figure attached (Innova). The ITX1200 itself is described as having a “Heavy Duty Steel Frame,” again without a number.

HARISON argues from shape rather than material. Its blog post on the HR-407 sets its “sturdy and unique triangular frame” against the “extra-wide tubular steel frame” of the Ironman Gravity, and says the triangle “has much better heavy load performance” (HARISON). Both tables are rated at the same 350 lb, so this is a comparison of geometry, made by one of the two makers, with no test result behind it.

The One Safety Margin We Found Published

The only figure we found that says how much stronger a frame is than its rating comes from Teeter, and only in one place. On the EP-560 product page, a customer asks about the weight limit, and the answer Teeter published on the page reads: “The weight limit for our inversion table is 300 lbs. at a 400% safety rating” (Teeter).

That is a statement about build margin, not a higher capacity: the table is still sold to hold 300 lb. It is also a customer-service answer rather than a line in the spec sheet, it does not say how the rating was tested or who confirmed it, and it does not appear on the X1, X3 or LX9 pages we read. Treat it as a claim about the EP-560, not about Teeter’s whole range.

What None of Them Publish, and What to Compare Instead

What is missing matters more. None of the three makers publishes a steel gauge or a tube wall thickness for its frames. Teeter’s pages call the steel “High Gauge Heat-Treated Steel” with no number attached (Teeter), and when we searched the four Teeter product pages and Innova’s full ITX9600 manual for gauge or millimeter figures, the only measurements we found were bolt sizes, which describe hardware, not the frame.

HARISON’s post gives a shape, not dimensions. There is no published construction figure you could use to compare one “heavy duty” frame with another.

So for weight, the number that counts is the capacity the maker publishes, which is what the rest of this page goes by. Compare the rated capacity on the maker’s own page or manual first, then the ankle system and the height range.

Why Searches for a 400 lb Capacity Show Tables That Don’t Invert

Search for an inversion table with a 400 lb capacity and you will find products that really do carry 400 lb. The problem is that they are not inversion tables.

The Sunny Health & Fitness Table Is a Traction Bench

The most visible example comes from Sunny Health & Fitness. Its manufacturer page calls the product a “Traction Reset Table for Stretch and Decompression” and says, in its own words, “Decompress without the challenges of inversion … A safer alternative to traditional inversion tables, this spinal decompression table accommodates users up to 400 LBS” (Sunny).

The 400 lb figure is genuine. But Sunny itself presents the product as an alternative to inversion: you lie on it flat, and it never turns you upside down.

That is not a flaw in the product. It is simply a different machine, and it answers a different question from the one you asked.

Traction Table vs Inversion Table: the Difference That Matters

An inversion table uses your own body weight, tipped head-down, to pull on the spine. A traction or decompression bench stretches you while you stay level. Because the bench does not have to hold a full adult upside down by the ankles, the engineering problem is different, and so is the capacity a maker can publish.

It also changes the risks. The dangers specific to inversion, such as the rise in blood pressure and eye pressure, and the fall onto the head if the ankles slip, come from being upside down. A flat bench avoids those.

What it does not avoid is the open question about traction itself: a Cochrane review published in 2013 pooled 32 trials and found that traction, alone or combined with other treatments, made little or no difference to pain, function or return to work in low-back pain (Wegner, 2013). That covers traction in general, including the kind these benches provide.

How to Spot One in a Listing

Look for words like “decompression,” “traction,” “stretch table” or “reset table,” and check whether the product photos show anyone tilted past horizontal. If the frame has no pivot and no ankle lock, it is a bench. Some listings put “inversion” in the title of a bench anyway, because that is the word people search for. Read the manufacturer’s description, not the title.

What About 500 and 600 lb Inversion Tables?

We looked for these too, because they are the numbers people search after 400. Beyond the Health Gear ITM7.5 covered above, there is exactly one manufacturer-published figure above 400 lb that we could trace, and it comes with serious caveats.

The Health Mark Pro Max: 600 lb on a 2023 Page

Health Mark published a Pro Max Inversion Table with a “Weight capacity: 600 pounds,” height settings “to accommodate heights of 4-ft. 10-in. to 6-ft. 11-in.,” a one-year limited warranty, and manufacture in Taiwan (Health Mark, 2023 archive). That is the manufacturer’s product page as archived by the Wayback Machine on May 29, 2023, the most recent capture available, and we have no current page from Health Mark showing the table is still sold.

On that same archived page, the product was already marked “Out of stock.”

Why It Isn’t a Recommendation

Put those two facts together and you have a historical spec, not a table you can buy with confidence. We don’t know whether the Pro Max came back into stock, was discontinued for good, or changed since 2023.

A one-year warranty is also only as useful as the maker’s ability to honor it on a product it may no longer carry. So we are telling you it existed, because it is the only published 600 lb figure we found, and not pointing you to buy it. If you want to pursue it, contact Health Mark directly and ask whether the Pro Max is still made, before you order it from anyone.

Titles and Video Names Aren’t Specs

When we looked at what ranks for 500 and 600 lb searches, much of it was not a spec at all: a video called something with “600” in the name, a page whose title promised a high capacity while its own text gave a lower one, and the same 350 lb and 400 lb products from above. The only test that works is the one we used throughout this page: find the manufacturer’s own statement of the capacity.

Weight Is Not Only About the Frame

Even a table rated for your weight leaves one part of the system unrated: you. The frame holds the load, but your ankles and feet are what hold you on the frame.

Your Ankles Carry Your Whole Weight Upside Down

When you invert, the ankle clamp and your ankle joints hold your full body weight against gravity. The heavier you are, the more load goes through them. Innova’s manual lists “Weak ankles and/or feet” among the conditions that should keep you off the table without a doctor’s approval (Innova). That item is on Innova’s list and not on Teeter’s, and it is the one most directly tied to how inversion accidents happen.

Joe Rogan made a related point when he explained why he prefers Teeter’s DEX II, which he says avoids pulling on the knees and ankles; our page on what Rogan actually said about Teeter covers it, and the DEX II section above explains how it holds you.

The Makers Themselves List Weight as a Reason to Ask a Doctor

The same Innova list includes “Overweight” and “Extremely Obese” (Innova). Teeter’s list, which the company says also appears in its owner’s manual, puts obesity among the conditions where exercise may be restricted by a physician (Teeter). These are manufacturer lists, written with legal caution, not findings from a trial. But when both leading brands tell heavier users to get medical approval first, a higher-capacity frame is not a substitute for that conversation.

What the Fall Case Reports Recommend

The most serious documented risk is falling. In a 2021 report on three cervical spinal cord injuries after inversion table falls, the authors describe the mechanism as resembling a diving injury: once ankle strength is lost or the foot slips, the user lands on the top of the head (Jung, 2021). They recommend keeping sessions under one minute, placing an angled pillow or rubber ramp under the head so a slip becomes a slide, and they single out older and heavier users with weaker ankle strength as needing extra caution.

It is three cases, so it tells you nothing about how often this happens, and the recommendations are the authors’ own rather than a clinical consensus. They are still the most specific advice we found for heavier users.

Why the Ankle Clamp Matters More at Higher Weights

Ankle systems have failed before. In 2010 the U.S. Consumer Product Safety Commission announced a recall of about 33,000 inversion benches from three brands after 75 reports of the ankle clamp releasing or the rotation strap breaking, including 23 injuries, some to the head and neck (CPSC, 2010). Those were specific older models, not any table on this page.

For a fuller look at what can go wrong, see our page on inversion table side effects.

If You Weigh More Than 350 lb

This is the situation where a straight answer matters most, so here it is: we could not verify an inversion table rated for you, and we would rather say that than send you to one that isn’t.

Start With Your Doctor

Both Innova and Teeter tell heavier users to get a physician’s approval before inverting, and inversion raises blood pressure: in a small trial, two minutes upside down raised both systolic and diastolic pressure in healthy young women (Haskvitz, 1986). That sample was young and healthy, so it can’t tell you the size of the effect for you, which is exactly why the conversation belongs with someone who can examine you. Our page on who should not use an inversion table goes through each condition on the makers’ lists, with the evidence behind it.

Don’t Exceed the Published Rating

A 350 lb rating is the manufacturer’s maximum. Going over it means using the table outside what the maker says it was built for, and on a device that holds you head-down by the ankles, that is not a margin worth testing. If you are close to 350 lb, the ITX1200 is the verified table we can link, the DEX II is the verified alternative that spares your ankles, and we would not treat either rating as a target.

A Flat Traction Bench Is a Different Choice, Not a Bigger Inversion Table

If what you want is a stretch for your back and your weight is above every verified inversion rating, a traction or decompression bench is the category that publishes higher capacities, with Sunny’s bench at 400 lb as one example (Sunny). Be clear about what you are choosing. It is a different device with a different mechanism, it does not invert you, and the Cochrane evidence on traction for low-back pain, as described above, is not encouraging. Treat it as a separate decision and ask your doctor about it on those terms, not as a heavier-duty version of the same thing.

Inversion Table Weight Limits: How to Check One Yourself

Listings change, and new tables will appear after we publish this. An inversion table’s weight limit is only as good as its source, so here is how to check any of them the way we checked these.

Go to the Manufacturer, Not the Listing

Find the brand’s own website and look for the capacity on the product page or in the owner’s manual. We found a listing for one popular table claiming a higher capacity than its maker publishes, which is why we always side with the maker. If a brand has no website of its own, or its site is no longer operating, treat any capacity you see as unverified. Capacity is also not the same as build quality, but a heavy duty inversion table label is not something you can verify either: as we showed in the section on heavy duty inversion tables rated for 400 lbs, no maker we checked publishes a frame figure you could compare.

Check That It Actually Inverts

Look for a pivot, an ankle lock and photos of someone tilted past horizontal. If the product description talks about decompression while you stay flat, or calls itself an alternative to inversion, it is a bench, and its capacity does not answer your question.

Check Height as Well as Weight

A higher weight rating does not come with a higher height limit. Every Innova and Teeter table we checked stops at 6’6”, including the 350 lb ITX1200. If you are both tall and heavy, the height limit may rule a table out before the weight does.

Check the Warranty and Who Stands Behind It

Warranty terms differ more than capacities do. Innova’s is one year and applies only to the original purchaser from an authorized retailer. HARISON’s store page states 12 months. Teeter includes a five-year full warranty on its FitSpine tables (Teeter), but its inversion tables stop at 300 lb; only the DEX II, which is not a table, goes to 350.

If you are buying at the top of a table’s rated range, the length of the warranty and whether the maker is still in business both matter more than usual. For every use case below 350 lb, including tables with longer warranties, see our full guide to the best inversion tables.

Your questions, answered

Frequently Asked Questions

How much weight can an inversion table support?

Most support 300 lb, and that is the figure Teeter and Innova publish across nearly all their models. The highest current rating we could confirm with a manufacturer is 350 lb, on the Innova ITX1200, the HARISON HR-407 and the Ironman Gravity 4000. Anything advertised at 400 lb or more was either a traction bench that never tips you upside down or a product we could not confirm is still sold.

Can overweight people use an inversion table?

Some can, but it calls for a doctor's opinion first. Innova's manual lists being overweight or extremely obese among the conditions that need a physician's approval, and Teeter's list includes obesity too. The frame is only half of it: your ankles hold your full weight upside down, and the authors of a 2021 case series flagged heavier users as needing extra care against falls.

Is there an inversion table suitable for a 300-pound person?

Yes. At 300 lb you are at the published limit of most Teeter and Innova tables, which leaves no margin at all. The Innova ITX1200 is rated to 350 lb by Innova itself, which gives you 50 lb of headroom and the same 4'10" to 6'6" height range as the rest of the brand. Check your height against that range too, and get a doctor's go-ahead first.

20 sources used for this guide

Each linked to the original. Citations in the text jump here.

View sources
  1. Innova. ITX1200 Inversion Table. innovaproductsinc.com, product page.

  2. HARISON FITNESS LTD. HARISON Best Inversion Table HR-407 for Big People (post do blog). harisonfitness.com/harison-best-inversion-table-hr-407/.

  3. Ironman Fitness (Paradigm Health & Wellness Inc.). Ironman Fitness Gravity 4000 Owner's Manual. Owner's manual, hosted on ManualsLib.

  4. Extreme Products Group (Health Gear). ITM 7.5 Big & Tall Inversion Table. extremeproductsgroup.com product page, as archived by the Wayback Machine on October 9, 2024.

  5. Extreme Products Group, LLC. Extreme Products Group, LLC has ceased operations. extremeproductsgroup.com, as archived by the Wayback Machine on January 20, 2025.

  6. BankruptcyObserver. EXTREME PRODUCTS GROUP, LLC Chapter 7 Bankruptcy 2025. bankruptcyobserver.com, sourced from PACER.

  7. Innova. ITX9600 Heavy Duty Deluxe Inversion Therapy Table, Owner's Manual (version 1709AJJ). Innova Products Inc., owner's manual.

  8. HARISON FITNESS LTD. HARISON HR-407 Inversion Table (ficha de loja). harisonfitness.com/product/inversion-table-407/.

  9. Teeter. FitSpine X3 Inversion Table. teeter.com, product page.

  10. Teeter. EP-560 Inversion Table. teeter.com, product page.

  11. Teeter. FitSpine X1 Inversion Table. teeter.com, product page.

  12. Sunny Health & Fitness. Traction Reset Table (para Stretch e Decompressao), SF-BH623052. sunnyhealthfitness.com.

  13. Wegner I, Widyahening IS, van Tulder MW et al. Traction for low-back pain with or without sciatica. Cochrane Database of Systematic Reviews 2013, CD003010.

  14. Health Mark, Inc. Pro Max Inversion Table - Back Inversion Table. healthmarkinc.us product page, as archived by the Wayback Machine on May 29, 2023.

  15. Teeter. Are there health issues that would prevent me from inverting?. teeter.com, Support Center (the same list appears in the owner's manual).

  16. Jung SH, Hwang JM, Kim CH. Inversion Table Fall Injury, the Phantom Menace: Three Case Reports on Cervical Spinal Cord Injury. Healthcare (Basel) 2021;9(5):492.

  17. CPSC. ICON Health & Fitness Recalls Inversion Benches Due to Fall Hazard. U.S. Consumer Product Safety Commission, cpsc.gov, recall 10-210, April 28, 2010.

  18. Haskvitz EM, Hanten WP. Blood pressure response to inversion traction. Physical Therapy 1986;66(9):1361-1364.

  19. Teeter. DEX II Commercial Inversion & Core Training System. teeter.com, accessed September 2026.

  20. Teeter. DEX II Inversion & Core Training System: Assembly & User Guide. Owner's manual, label D12010.

Search IntoInversion